Type T2: Screw Terminals, One-Piece Band
Standard Termination Location: opposite the gap; center of the width
Minimum Inside Diameter: 2″ (50.8 mm)
Minimum Width: 1″ (25.4 mm)
Maximum Volts/Amps: 480VAC/25A
Type T2: Screw Terminals, Two-Piece Band
Standard Termination Location: center of each half; center of the width
Minimum Inside Diameter: 4″ (101.6 mm)
Minimum Width: 1″ (25.4 mm)
Maximum Volts/Amps: 480VAC/25A each half
Type T3: Screw Terminals, One-Piece Band
Standard Termination Location: opposite the gap; across the center of the width
Minimum Inside Diameter: 2″ (50.8 mm)
Minimum Width: 2″ (50.8 mm)
Maximum Volts/Amps: 480VAC/25A
Type T3: Screw Terminals, Two-Piece Band
Standard Termination Location: center of each half; across the center of the width
Minimum Inside Diameter: 4″ (101.6 mm)
Minimum Width: 2″ (50.8 mm)
Maximum Volts/Amps: 480VAC/25A each half
Type L1: Straight Lead Wires, One-Piece Band
Standard Termination Location: opposite the gap; center of the width
Minimum Inside Diameter: 2″ (50.8 mm)
Minimum Width: 1″ (25.4 mm)
Maximum Volts/Amps: 480VAC/10A
Type L1: Straight Lead Wires, Two-Piece Band
Standard Termination Location: center of each half; center of the width
Minimum Inside Diameter: 4″ (101.6 mm)
Minimum Width: 1″ (25.4 mm)
Maximum Volts/Amps: 480VAC/10A each half
Type W1: Abrasion Resistant Straight Wire Braid Leads, One-Piece Band
Standard Termination Location: opposite the gap; center of the width
Minimum Inside Diameter: 2″ (50.8 mm)
Minimum Width: 1″ (25.4 mm)
Maximum Volts/Amps: 480VAC/10A
Type W1: Abrasion Resistant Straight Wire Braid Leads, Two-Piece Band
Standard Termination Location: center of each half; center of the width
Minimum Inside Diameter: 4″ (101.6 mm)
Minimum Width: 1″ (25.4 mm)
Maximum Volts/Amps: 480VAC/10A each half
Type R1: Abrasion Resistant Straight Armor Cable, One-Piece Band
Standard Termination Location: opposite the gap; center of the width
Minimum Inside Diameter: 2″ (50.8 mm)
Minimum Width: 1″ (25.4 mm)
Maximum Volts/Amps: 480VAC/10A
Type R1: Two-Piece Band Abrasion Resistant Straight Armor Cable
Standard Termination Location: center of each half; center of the width
Minimum Inside Diameter: 4″ (101.6 mm)
Minimum Width: 1″ (25.4 mm)
Maximum Volts/Amps: 480VAC/10A each half
Type R2: Abrasion Resistant Right-Angle Armor Cable, One-Piece Band
Standard Termination Location: opposite the gap; center of the width
Minimum Inside Diameter: 2″ (50.8 mm)
Minimum Width: 1″ (25.4 mm)
Maximum Volts/Amps: 480VAC/10A
Type R2: Abrasion Resistant Right-Angle Armor Cable, Two-Piece Band
Standard Termination Location: center of each half; center of the width
Minimum Inside Diameter: 4″ (101.6 mm)
Minimum Width: 1″ (25.4 mm)
Maximum Volts/Amps: 480VAC/10A each half
Type S1: Lead Wire Spring Strain Relief, One-Piece Band
Standard Termination Location: opposite the gap; center of the width
Minimum Inside Diameter: 2″ (50.8 mm)
Minimum Width: 1″ (25.4 mm)
Maximum Volts/Amps: 480VAC/10A
Type S1: Lead Wire Spring Strain Relief, Two-Piece Band
Standard Termination Location: center of each half; center of the width
Minimum Inside Diameter: 4″ (101.6 mm)
Minimum Width: 1″ (25.4 mm)
Maximum Volts/Amps: 480VAC/10A each half
Type C2: Standard Terminal Box, One-Piece Band
Standard Termination Location: opposite the gap; center of the width
Minimum Inside Diameter: 2″ (50.8 mm)
Minimum Width: 1-1/2″ (38.1 mm)
Maximum Volts/Amps: 480VAC/25A
Type C2: Standard Terminal Box, Two-Piece Band
Standard Termination Location: center of each half; center of the width
Minimum Inside Diameter: 4″ (101.6 mm)
Minimum Width: 1-1/2″ (38.1 mm)
Maximum Volts/Amps: 480VAC/25A each half
Type C5: Low-Profile Terminal Box, One-Piece Band
Standard Termination Location: opposite the gap; center of the width
Minimum Inside Diameter: 2″ (50.8 mm)
Minimum Width: 1-1/2″ (38.1 mm)
Maximum Volts/Amps: 480VAC/25A
Type C5: Low-Profile Terminal Box, Two-Piece Band
Standard Termination Location: center of each half; center of the width
Minimum Inside Diameter: 4″ (101.6 mm)
Minimum Width: 1-1/2″ (38.1 mm)
Maximum Volts/Amps: 480VAC/25A each half
Type P1: High-Temperature Quick Disconnect Plugs, One-Piece Band
Standard Termination Location: opposite the gap; center of the width
Minimum Inside Diameter: 2″ (50.8 mm)
Minimum Width: 2″ (50.8 mm) depending on termination orientation
Type P1: High-Temperature Quick Disconnect Plugs, Two-Piece Band
Standard Termination Location: center of each half; center of the width
Minimum Inside Diameter: 4″ (101.6 mm)
Minimum Width: 2″ (50.8 mm) depending on termination orientation
Type P2: High-Temperature Quick Disconnect Plugs, Low-Profile, One-Piece Band
Standard Termination Location: opposite the gap; center of the width
Minimum Inside Diameter: 2″ (50.8 mm)
Minimum Width: 2″ (50.8 mm)
Type P2: High-Temperature Quick Disconnect Plugs, Low-Profile, Two-Piece Band
Standard Termination Location: center of each half; center of width
Minimum Inside Diameter: 4″ (101.6 mm)
Minimum Width: 2″ (50.8 mm)
Type P3: DIN 49458 A/B Quick Disconnect Plugs, Vertical, One-Piece Band
Standard Termination Location: opposite the gap; center of width
Minimum Inside Diameter: 3″ (76.2 mm)
Minimum Width: 2″ (50.8 mm)
Type P3: DIN 49458 A/B Quick Disconnect Plugs, Vertical, Two-Piece Band
Standard Termination Location: center of each half; center of width
Minimum Inside Diameter: 4″ (101.6 mm)
Minimum Width: 2″ (50.8 mm)
Type P4: DIN 49458 A/B Quick Disconnect Plugs, Horizontal, One-Piece Band
Standard Termination Location: opposite the gap; center of width
Minimum Inside Diameter: 2-1/2″ (63.5 mm)
Minimum Width: 2-1/2″ (63.5 mm)
Type P4: DIN 49458 A/B Quick Disconnect Plugs, Horizontal, Two-Piece Band
Standard Termination Location: center of each half; center of width
Minimum Inside Diameter: 4″ (101.6 mm)
Minimum Width: 2-1/2″ (63.5 mm)