Excel Automation is an authorized East Coast Sensors distributor. Contact us with sales and technical support.
| 1 Series |
2 Calibration |
3 Sheath Diameter |
4 Bend Type |
5 6 Sheath Length |
7 Junction |
8 Lead Wire Material |
9 Lead Wire Length |
10 Termination Style |
11 Special Features |
12 Attached Fitting |
13 14 Insertion Length |
|---|---|---|---|---|---|---|---|---|---|---|---|
| TB2 |
| 2 | Calibration |
|---|---|
| J | Type J |
| K | Type K |
| T | Type T |
| E | Type E |
| 3 | Sheath Diameter |
|---|---|
| G | 0.118″ (3mm) |
| H | 0.125″ (3.2mm) (1/8″) |
| J | 0.156″ (4mm) |
| L | 0.188″ (4.8mm) (3/16″) (standard) |
| S | 0.195″ (5mm) |
| M | 0.236″ (6mm) |
| N | 0.250″ (6.4mm) (1/4″) |
| P | 0.314″ (8mm) (5/16″) |
| Q | 0.375″ (9.5mm) (3/8″) |
| Sizes for reference only (Standard tolerances apply) |
| 4 | Bend Type |
|---|---|
| X |  Straight (standard) |
| Y |  90 Degree bend |
| Z |  45 Degree bend |
| 5 6 | Sheath Length |
|---|---|
| ¼-600 |
| 7 | Junction |
|---|---|
| G |  Grounded (standard) |
| U |  Ungrounded |
| W |  Grounded (Dual Junction) |
| Y |  Ungrounded Common (Dual) |
| 8 | Lead Wire Material |
|---|---|
| A |  Fiberglass (800°F) |
| B |  Fluoropolymer (400°F) |
| C |  Polyimide (500°F) |
| E |  High temperature fiberglass (1200°F) |
| F |  Fiberglass with stainless steel braid (800°F) (standard) |
| G |  Fluoropolymer with stainless steel braid (400°F) |
| H |  Fiberglass with armor cable (800°F) (standard) |
| J |  Fluoropolymer with armor cable (400°F) |
| K |  Polyimide with armor cable (500°F) |
| L |  High temperature fiberglass with armor cable (1200°F) |
| M |  Fiberglass with stainless steel braid with armor cable (800°F) |
| W |  Fluoropolymer with stainless steel braid with armor cable (400°F) |
| Y |  Fluoropolymer with stainless steel braid with Fluoropolymer outer jacket (400°F) |
| Wire gauge determined by ECS based on sheath diameter |
| 9 | Lead Wire Length |
|---|---|
| 6-999 |
| Over 999″ contact factory |
| 10 | Termination Style |
|---|---|
| A |  2″ stripped leads (bare ends) |
| B |  2″ stripped leads w/ spade lugs |
| C |  Standard male plug (400°F) |
| D |  High temp male plug (660°F) |
| E |  Max temp male plug (800°F) |
| F |  Ceramic male plug (1200°F) |
| G |  Solid pin plug |
| H |  Standard female jack (400°F) |
| J |  Miniature plug (400°F) |
| K |  Miniature jack (400°F) |
| L |  2″ stripped leads w/ #6 Ring terminals |
| N |  Standard 3 pin plug w/ ground wire (400°F) |
| P |  Dual molded male plug (400°F) |
| W |  2” stripped leads w/ pin terminals |
| Q |  2” stripped leads w/ wire ferrules |
| X |  Extra long lead wire length (beyond 2” stripped leads) |
| 11 | Special Features |
|---|---|
| None | |
| 01 |  Solid conductor (Lead wire) |
| 02 |  1.5″ long strain relief spring |
| 03 |  1.5″ long heat shrink where wire exits the probe |
| 04 |  Flat tip probe |
| 05 |  Drill point tip |
| 06 |  Epoxy seal |
| 07 |  Cable Clamp |
| 08 |  Bx Connector |
| 09 |  Mating connector
|
| 11 |  International IEC 584-3 color coded leads |
| 12 |  British color coded leads |
| 13 |  German color coded leads |
| 14 |  Japanese color coded leads |
| 15 | Reverse polarity color coded leads |
| 16 |  French color coded leads |
| 18 |  Moisture protection boot on connector |
| 21 |  Fluoropolymer coated armor cable |
| 24 |  Fluoropolymer covered probe |
| 25 |  Free spinning fitting (held on probe by a crimp ring) |
| 27 |  Transition fitting on tube & wire sensor |
| 12 | Attached Fitting (optional) |
|---|---|
| None | |
| F01 |  1/8″ npt single thread |
| F02 |  1/4″ npt single thread |
| F03 |  3/8″ npt single thread |
| F04 |  1/2″ npt single thread |
| F05 |  3/4″ npt single thread |
| F06 |  1/2″ npt x 1/2″ npt double thread |
| F07 |  1/2″ npt double thread. Spring loaded |
| F08 |  1/2″ npt x 1/2″ npt double thread. Spring loaded w/ oil seal |
| F09 |  1/2″ npt x 3/4″ npt double thread |
| F10 |  3/4″ npt x 3/4″ npt double thread |
| F16 |  Adjustable 7/16″ ID bayonet cap fitting (1/8″ OD & 3mm OD) |
| F17 |  Adjustable 12.5mm ID double slot bayonet cap fitting (1/8″ OD & 3mm OD) |
| F18 |  1/8″ npt compression fitting (Brass) |
| F19 |  1/8″ npt compression fitting (Stainless Steel) |
| F20 |  1/4″ npt compression fitting (Brass) |
| F21 |  1/4″ npt compression fitting (Stainless Steel) |
| F26 |  1/4″ npt double thread |
| For other fittings not shown contact factory |
- Dual junction only available in diameters 0.156″ and larger