Excel Automation is an authorized East Coast Sensors distributor. Contact us with sales and technical support.
Specifications| 1 Series |
2 Calibration |
3 Sheath Diameter |
4 Bend Type |
5 6 Sheath Length |
7 Wire Material |
8 Junction |
9 Termination Style |
10 Special Features |
11 Attached Fitting |
12 13 Isertion Length |
|---|---|---|---|---|---|---|---|---|---|---|
| TB3 |
| 2 | Calibration |
|---|---|
| J | Type J |
| K | Type K |
| T | Type T |
| E | Type E |
| 3 | Sheath Diameter |
|---|---|
| G | 0.118″ (3mm) |
| H | 0.125″ (3.2mm) (1/8″) |
| L | 0.188″ (4.8mm) (3/16″) (standard) |
| M | 0.236″ (6mm) |
| N | 0.250″ (6.4mm) (1/4″) |
| Sizes for reference only (Standard tolerances apply) | |
| For other diameters consult factory |
| 4 | Bend Type |
|---|---|
| X |  Straight (standard) |
| Y |  90 Degree bend |
| Z |  45 Degree bend |
| 5 6 | Sheath Length |
|---|---|
| ¼-600 |
| Wire Material | |
|---|---|
| A | Fiberglass (800°F) |
| B | Fluoropolymer (400°F) |
| 8 | Junction |
|---|---|
| G |  Grounded (standard) |
| U |  Ungrounded |
| W |  Grounded (Dual Junction) |
| Y |  Ungrounded Common (Dual) |
| 9 | Termination Style |
|---|---|
| C |  Standard male plug (400°F) |
| D |  High temp male plug (660°F) |
| E |  Max temp male plug (800°F) |
| G |  Solid pin plug |
| H |  Standard female jack (400°F) |
| J |  Miniature plug (400°F) |
| K |  Miniature jack (400°F) |
| N |  Standard 3 pin plug w/ ground wire (400°F) |
| P |  Dual molded male plug (400°F) |
| Z |  Dual molded female jack (400°F) |
| 10 | Special Features |
|---|---|
| None | |
| 04 |  Flat tip probe |
| 05 |  Drill point tip |
| 09 |  Mating connector
|
| 18 |  Moisture protection boot on connector |
| 24 |  Fluoropolymer covered probe |
| 25 |  Free spinning fitting (held on probe by a crimp ring) |
| 26 |  Connector mounted with tube adapter |
| 29 |  Silver soldered thermocouple junction |
| 11 | Attached Fitting (optional) |
|---|---|
| None | |
| F01 |  1/8″ npt single thread |
| F02 |  1/4″ npt single thread |
| F03 |  3/8″ npt single thread |
| F04 |  1/2″ npt single thread |
| F05 |  3/4″ npt single thread |
| F06 |  1/2″ npt x 1/2″ npt double thread |
| F07 |  1/2″ npt double thread. Spring loaded |
| F08 |  1/2″ npt x 1/2″ npt double thread. Spring loaded w/ oil seal |
| F09 |  1/2″ npt x 3/4″ npt double thread |
| F10 |  3/4″ npt x 3/4″ npt double thread |
| F11 |  Fixed 7/16″ ID single slot bayonet cap assembly |
| F14 |  1/2″ npt x 3″ npt double thread |
| F15 |  3″ npt single thread |
| F16 |  Adjustable 7/16″ ID bayonet cap fitting (1/8″ OD & 3mm OD) |
| F17 |  Adjustable 12.5mm ID double slot bayonet cap fitting (1/8″ OD & 3mm OD) |
| F18 |  1/8″ npt compression fitting (Brass) |
| F19 |  1/8″ npt compression fitting (Stainless Steel) |
| F20 |  1/4″ npt compression fitting (Brass) |
| F21 |  1/4″ npt compression fitting (Stainless Steel) |
| For other fittings not shown contact factory |