Excel Automation is an authorized distributor of Panasonic / Sunx products. Contact us with sales and application support.
Main unit
| Type | Spot type | ||
|---|---|---|---|
| Model No. | ER-VS02 | ER-VS01 | |
| CE marking directive compliance | EMC Directive, RoHS Directive | ||
| Charge removal time (±1,000 V → ±100 V) |
1 sec. or less (Note 2) | ||
| Ion balance | ±10 V or less (Note 2) | ||
| Ozone generation | 0.03 ppm or less (Note 3) | ||
| Applicable fluid | Air (dried clean air) (Note 4) | ||
| Supplied air flow | 500 ℓ/min. (ANR) or less (Note 5) | ||
| Air pressure range | 0.05 to 0.7 MPa (Note 5) | ||
| Supply voltage | 24 V DC ±10 % | ||
| Current consumption | 70 mA or less | ||
| Discharge method | High frequency AC method | ||
| Discharge output voltage | 2,000 V approx. | ||
| Check output(CHECK) | NPN open-collector transistor ・Maximum sink current: 50 mA ・Applied voltage: 30 V DC or less (between check output and 0 V) ・Residual voltage: 1 V or less (at 50 mA sink current) |
||
| Output operation | ON when a dirt or worn etc. of the discharge needle is detected for 1.5 sec. or more continuously, OFF when operation is normal (Note 6) | ||
| Short-circuit protection |
Incorporated | ||
| Error output(ERROR) | NPN open-collector transistor ・Maximum sink current: 50 mA ・Applied voltage: 30 V DC or less (between error output and 0 V) ・Residual voltage: 1 V or less (at 50 mA sink current) |
||
| Output operation | OFF when abnormal discharge is detected, ON when operation is normal | ||
| Short-circuit protection | Incorporated | ||
| Discharge halt input (DSC OFF) (Note 7) |
Short-circuit to 0 V: Discharge halt, Open: Discharge allowed (operation start) | ||
| Reset input | When abnormal discharge is detected, discharge is halted due to an error. Reset the discharge halt by briefly shorting the power supply’s 0 V line. | ||
| Indicators | Power(POWER) | Green LED (lights up when the power is ON) | |
| Discharge(DSC) (Note 7) | Green LED (lights up when discharging) | ||
| Check(CHECK) | Orange LED (lights up when the discharge needle is worn or dirty, etc.) (Note 6) | ||
| Error(ERROR) | Red LED (lights up when abnormal discharge is detected) | ||
| Environmental resistance | Ambient temperature | 0 to +55 ℃ +32 to +131 ℉ (No dew condensation allowed) | |
| Ambient humidity | 35 to 65 % RH | ||
| Vibration resistance | 10 to 150 Hz frequency, 0.75 mm 0.030 in double amplitude in X, Y and Z directions for two hours each | ||
| Cable | Cable with a connector, 0.5 m 1.640 ft long | ||
| Material | Enclosure: PPS, Cover: Stainless steel, Discharge needle: Tungsten | ||
| Weight | Net weight: 120 g approx. | ||
| Accessory | Connector for wiring: 1 set [Manufactured by Molex: Housing (5557-08R), Terminal (5556TL)] | ||
Nozzles / Tubes
| Type | Shower nozzle | Straight bar nozzle 200 mm 7.874 in |
Straight bar nozzle 320 mm 12.598 in |
Straight bar nozzle 650 mm 25.591 in |
|---|---|---|---|---|
| Model No. | ER-VAS | ER-VAB020 | ER-VAB032 | ER-VAB065 |
| Supplied air pressure range | 0.05 to 0.40 MPa | |||
| Charge removal range | – | 200 mm 7.874 in | 320 mm 12.598 in | 650 mm 25.591 in |
| Material | Stainless steel | |||
| Accessories | Attachment and insulation pipe: 1 pc. each | Attachment and insulation pipe: 1 pc. each, Straight bar nozzle holder: 1 set | ||
| Type | Shape-preserving tube joint nozzle | Conductive tube joint nozzle |
|---|---|---|
| Model No. | ER-VAJK | ER-VAJT-64 |
| Air pressure range | 0.02 to 0.5 MPa | 0.02 to 0.7 MPa .(Maximum applied pressure depends on the tube length. Refer to the following figure) |
| Material | Stainless steel | Stainless steel |
| Supplied air flow | 30 to 250 ℓ/min. (ANR) | 20 to 160 ℓ/min. (ANR) (at applied pressure of 0.02 to 0.7 MPa) |
| Accessories | Attachment (White): 1pc. Insulation pipe: 1pc. |
Attachment (White): 1pc. Insulation pipe: 1pc. |
| Type | Shape-preserving tube | Conductive tube | ||
|---|---|---|---|---|
| Model No. | ER-VAK10 | ER-VAK30 | ER-VAK50 | ER-AT50 |
| Tube length | 112 mm 4.409 in | 312 mm 12.283 in | 512 mm 20.157 in | 500 mm 19.685 in |
| Material | Tube interior: Aluminum Tube sheath: High-density polyethylene Terminal cap: Stainless steel |
Urethane | ||
| Air pressure range | 0.02 to 0.5 MPa | 0.02 to 0.7 MPa | ||
| Minimum bending radius | R40 mm R1.575 in or more | R15 mm R0.591 in or more | ||
| Type | Tube and joint set |
|---|---|
| Model No. | ER-VAB-AT |
| Compatible nozzles | Straight nozzle (effective charge removal length 320 mm 12.598 in or less) |
| Tube length | 500 mm 19.685 in |
| Material | Nozzle: Stainless steel (SUS), Conductive tube: Urethane |
| Supplied air flow | Max. 200 ℓ/min. (ANR) |
| Air pressure range | 0.05 to 0.4 MPa |
| Minimum bending radius | R25 mm R0.984 in (conductive tube portion) |
| Accessories | Attachment (Black) 1 pc., insulated pipe: 1pc., Straight bar nozzle holder: 1 set |