Type T2: Screw Terminals, One-Piece Band
Standard Termination Location: opposite the gap; center of the width
Minimum Inside Diameter: 2-1/2″ (63.5 mm)
Minimum Width: 1-1/2″ (38.1 mm)
Post Terminals: 10-32 or 8-32
Maximum Volts: 480VAC
Maximum Amps: 25A (10-32) or 20A (8-32)
Type T2: Screw Terminals, Two-Piece Band
Standard Termination Location: center each half; center of width
Minimum Inside Diameter: 3″ (76.2 mm)
Minimum Width: 1-1/2″ (38.1 mm)
Post Terminals: 10-32 or 8-32
Maximum Volts/Amps: 480VAC/ 25A (10-32) or 20A (8-32) each half
Type T2: Screw Terminals, One-Piece Expandable Band
Standard Termination Location: center each half; center of width
Minimum Inside Diameter: 2-1/2″ (63.5 mm)
Minimum Width: 1-1/2″ (38.1 mm)
Post Terminals: 10-32 or 8-32
Maximum Volts/Amps: 480VAC/ 25A (10-32) or 20A (8-32) each half
Type T3X: Screw Terminals, One-Piece Band
Standard Termination Location: opposite the gap; across the center of the width
Minimum Inside Diameter: 2-1/2″ (63.5 mm)
Minimum Width:
with 10-32 Post Terminals — 2-1/2″ (63.5 mm)
with 8-32 Post Terminals — 2″ (50.8 mm)
Maximum Volts/Amps: 480VAC/ 25A (10-32) or 20A (8-32) each half
Type T3X: Screw Terminals, Two-Piece Band
Standard Termination Location: opposite the gap; across center of width
Minimum Inside Diameter: 3″ (76.2 mm)
Minimum Width:
with 10-32 Post Terminals — 2-1/2″ (63.5 mm)
with 8-32 Post Terminals — 2″ (50.8 mm)
Maximum Volts/Amps: 480VAC/ 25A (10-32) or 20A (8-32) each half
Type T3X: Screw Terminals, One-Piece Expandable Band
Standard Termination Location: opposite the gap; across the center of the width
Minimum Inside Diameter: 2-1/2″ (63.5 mm)
Minimum Width:
with 10-32 Post Terminals — 2-1/2″ (63.5 mm)
with 8-32 Post Terminals — 2″ (50.8 mm)
Maximum Volts/Amps: 480VAC/ 25A (10-32) or 20A (8-32) each half
Type T3Y: Screw Terminals, Two-Piece Band
Standard Termination Location: next to the same gap on each half; across the center of the width
Minimum Inside Diameter: 3″ (76.2 mm)
Minimum Width:
with 8-32 Post Terminals — 2″ (50.8 mm)
with 10-32 Post Terminals — 2-1/2″ (63.5 mm)
Maximum Volts: 480VAC each half
Maximum Amps: 25A (10-32) or 20A (8-32) each half
Type W1: Abrasion-Resistant Straight Wire Braid Leads, One-Piece Band
Standard Termination Location: opposite the gap; center of the width
Minimum Inside Diameter: 1″ (25.4 mm)
Minimum Width: 1″ (25.4 mm)
Maximum Volts: 480VAC
Maximum Amps: 10
Type W1: Abrasion-Resistant Straight Wire Braid Leads, Two-Piece Band
Standard Termination Location: center of each half; center of the width
Minimum Inside Diameter: 3″ (76.2 mm)
Minimum Width: 1″ (25.4 mm)
Maximum Volts: 480VAC each half
Maximum Amps: 10 each half
Type W1: Abrasion-Resistant Straight Wire Braid Leads, One-Piece Expandable Band
Standard Termination Location: two sets of leads opposite the gap; center of the width
Minimum Inside Diameter: 2-1/2″ (63.5 mm)
Minimum Width: 1-1/2″ (38.1 mm)
Maximum Volts/Amps: 480VAC/10A each half
Type W2: Right-Angle Wire Braid Leads, 90 Degrees to Heater Diameter, One-Piece Band
Standard Termination Location: opposite the gap; the near edge of the width
Minimum Inside Diameter: 1″ (25.4 mm)
Minimum Width: 1″ (25.4 mm)
Maximum Volts: 480VAC
Maximum Amps: 10
Type W2: Right-Angle Wire Braid Leads, 90 Degrees to Heater Diameter, Two-Piece Band
Standard Termination Location: center of each half; near the edge of the width
Minimum Inside Diameter: 3″ (76.2 mm)
Minimum Width: 1″ (25.4 mm)
Maximum Volts/Amps: 480VAC/10A each half
Type W5: Right-Angle Wire Braid Leads, 90 Degrees to Heater Width, One-Piece Band
Standard Termination Location: opposite the gap; center of the width
Minimum Inside Diameter: 1″ (25.4 mm)
Minimum Width: 1″ (25.4 mm)
Maximum Volts: 480VAC
Maximum Amps: 10
Type W5: Right-Angle Wire Braid Leads, 90 Degrees to Heater Width, Two-Piece Band
Standard Termination Location: center of each half; center of width
Minimum Inside Diameter: 3″ (76.2 mm)
Minimum Width: 1″ (25.4 mm)
Maximum Volts: 480VAC each half
Maximum Amps: 10 each half
Type R1: Abrasion-Resistant Straight Armor Cable, One-Piece Band
Standard Termination Location: opposite the gap; center of the width
Minimum Inside Diameter: 1″ (25.4 mm)
Minimum Width: 1″ (25.4 mm)
Maximum Volts: 480VAC
Maximum Amps: 10
Type R1: Abrasion-Resistant Straight Armor Cable, Two-Piece Band
Standard Termination Location: center of each half; center of the width
Minimum Inside Diameter: 3″ (76.2 mm)
Minimum Width: 1″ (25.4 mm)
Maximum Volts/Amps: 480VAC/10A each half
Type R1: Abrasion-Resistant Straight Armor Cable, One-Piece Expandable Band
Standard Termination Location: two sets of leads opposite the gap; center of the width
Minimum Inside Diameter: 2-1/2″ (63.5 mm)
Minimum Width: 1-1/2″ (38.1 mm)
Maximum Volts/Amps: 480VAC/10A each half
Type R2B: Abrasion-Resistant Right Angle Armor Cable, One-Piece Band
Standard Termination Location: opposite the gap; center of the width
Minimum Inside Diameter: 1″ (25.4 mm)
Minimum Width: 1″ (25.4 mm)
Maximum Volts/Amps: 480VAC/10A
Type R2B: Abrasion-Resistant Right Angle Armor Cable, Two-Piece Band
Standard Termination Location: center of each half; center of the width
Minimum Inside Diameter: 3″ (76.2 mm)
Minimum Width: 1″ (25.4 mm)
Maximum Volts/Amps: 480VAC/10A each half
Type R2B: Abrasion-Resistant Right Angle Armor Cable, One-Piece Expandable Band
Standard Termination Location: two sets of leads opposite the gap; center of the width
Minimum Inside Diameter: 2-1/2″ (63.5 mm)
Minimum Width: 1-1/2″ (38.1 mm)
Maximum Volts/Amps: 480VAC/10A each half
Type R2H: Abrasion-Resistant Right Angle Armor Cable for Type HTL Lead Wire, One-Piece Band
Standard Termination Location: opposite the gap; center of the width
Minimum Inside Diameter: 1-1/2″ (38.1 mm)
Minimum Width: 1″ (25.4 mm)
Maximum Volts/Amps: 480VAC/10A
Type R2H: Abrasion-Resistant Right Angle Armor Cable for Type HTL Lead Wire, Two-Piece Band
Standard Termination Location: center of each half; center of the width
Minimum Inside Diameter: 3″ (76.2 mm)
Minimum Width: 1″ (25.4 mm)
Maximum Volts/Amps: 480VAC/10A each half
Type R2H: Abrasion-Resistant Right Angle Armor Cable for Type HTL Lead Wire, One-Piece Expandable Band
Standard Termination Location: two sets of leads opposite the gap; center of the width
Minimum Inside Diameter: 2-1/2″ (63.5 mm)
Minimum Width: 1-1/2″ (38.1 mm)
Maximum Volts/Amps: 480VAC/10A each half
Type C: General Purpose Terminal Box, One-Piece Band
Standard Termination Location: opposite the gap; center of the width
Minimum Inside Diameter: 3″ (76.2 mm)
Minimum Width: 2″ (50.8 mm)
Maximum Volts/Amps: 480VAC/25A
Type C: General Purpose Terminal Box, Two-Piece Band
Standard Termination Location: center of each half; center of the width
Minimum Inside Diameter: 3″ (76.2 mm)
Minimum Width: 2″ (50.8 mm)
Maximum Volts/Amps: 480VAC/25A each half
Type C: General Purpose Terminal Box, One-Piece Expandable Band
Standard Termination Location: opposite the gap; center of the width
Minimum Inside Diameter: 3″ (76.2 mm)
Minimum Width: 2″ (50.8 mm)
Maximum Volts/Amps: 480VAC/25A each half
Type L1: Plain Wire Leads, One-Piece Band
Standard Termination Location: opposite the gap; center of the width
Minimum Inside Diameter: 1″ (25.4 mm)
Minimum Width: 1″ (25.4 mm)
Maximum Volts/Amps: 480VAC/10A
Type L1: Plain Wire Leads, Two-Piece Band
Standard Termination Location: center of each half; center of the width
Minimum Inside Diameter: 3″ (76.2 mm)
Minimum Width: 1″ (25.4 mm)
Maximum Volts/Amps: 480VAC/10A each half
Type L1: Plain Wire Leads, One-Piece Expandable Band
Standard Termination Location: two sets of leads opposite the gap; center of the width
Minimum Inside Diameter: 2-1/2″ (63.5 mm)
Minimum Width: 1-1/2″ (38.1 mm)
Maximum Volts/Amps: 480VAC/10A each half
Type P1: High-Temperature Quick Disconnect Plugs, One-Piece Band
Standard Termination Location: opposite the gap; center of the width
Minimum Inside Diameter: 3″ (76.2 mm)
Minimum Width: 2″ (50.8 mm)
Maximum Volts: 250VAC Maximum Amps: 16
Maximum Temperature: 572°F (300°C)
Type P1: High-Temperature Quick Disconnect Plugs, Two-Piece Band
Standard Termination Location: opposite the gap; center of the width
Minimum Inside Diameter: 3″ (76.2 mm)
Minimum Width: 2″ (50.8 mm)
Maximum Volts: 250VAC Maximum Amps: 16
Maximum Temperature: 572°F (300°C)
Type P2: Terminal Box and High-Temperature Quick Disconnect Straight Plug, One-Piece Band
Standard Termination Location: opposite the gap; center of the width
Minimum Inside Diameter: 3″ (76.2 mm)
Minimum Width: 2″ (50.8 mm)
Maximum Volts: 250VAC Maximum Amps: 16
Maximum Temperature: 572°F (300°C)
Type P2: Terminal Box and High-Temperature Quick Disconnect Straight Plug, Two-Piece Band
Standard Termination Location: center of each half; center of the width
Minimum Inside Diameter: 3″ (76.2 mm)
Minimum Width: 2″ (50.8 mm)
Maximum Volts: 250VAC each half Maximum Amps: 16 each half
Maximum Temperature: 572°F (300°C)
Type P2: Terminal Box and High-Temperature Quick Disconnect Straight Plug, One-Piece Expandable Band
Standard Termination Location: opposite the gap; center of the width
Minimum Inside Diameter: 3″ (76.2 mm)
Minimum Width: 2″ (50.8 mm)
Maximum Volts: 250VAC each half Maximum Amps: 16 each half
Maximum Temperature: 572°F (300°C)